A small cylindrical reed sensor 25.4mm x 6.22mm (1.00" x 0.245") with a choice of normally open, normally closed or change over contacts.
A miniature PCB mounting reed sensor 17.78mm x 4.32mm x 3.30mm(0.700" x 0.170" x 0.130mm) with a normally open contact.
A small PCB mounting reed sensor 22.86mm x 6.73mm x 4.57mm(0.900" x 0.265" x 0.180mm) with a choice of normally open, normally closed or change over contacts.
A small stainless steel barrel sensor with an M8 x 1.25mm pitch thread, 36mm (1.420") long with a choice of normally open, normally open high voltage, normally closed or change over contacts.
A small plastic barrel sensor with a 5/16" x 24 thread, 38.1mm (1.500") long with a choice of normally open, normally open high voltage, normally closed or change over contacts.
A small plastic barrel sensor with an M8 x 1.25mm pitch thread, 38.1mm (1.500") long with a choice of normally open, normally open high voltage, normally closed or change over contacts.
A robust stainless steel barrel sensor with an M12 x 1mm pitch thread, 46mm (1.810") long with a choice of normally open, normally open high voltage, normally closed or change over contacts.
A reed sensor with integral actuator magnet. Actuation occurs when a suitable vane passes through the slot between the magnet and switch. Normally open, normally closed, high voltage normally closed or changeover contacts.
A robust reed sensor with integral actuator magnet. Actuation occurs when a suitable vane passes through the slot between the magnet and switch. Normally closed, high voltage normally closed or changeover contacts.
A flange mounting reed sensor 28.57mm x 19.05mm x 6.35mm (1.125" x 0.750" x 0.259") with an integral 2 pin connector. Choice of normally open, normally open high voltage or normally closed contacts.
A flange mounting reed sensor 28.57mm x 19.05mm x 6.35mm (1.125" x 0.750" x 0.259") with integral terminal pins. Choice of normally open, normally open high voltage or normally closed contacts.
A high temperature flange mounting reed sensor 28.57mm x 19.05mm x 6.35mm (1.125" x 0.750" x 0.259") with a choice of normally open, normally open high voltage, normally closed or changeover contacts.
A miniature flange mounting reed sensor occupying only 3.22cm² (0.500"² ) board space with a choice of normally open, normally open high voltage, normally closed or changeover contacts.
A miniature flange mounting reed sensor occupying only 3.22cm² (0.500"²) board space with a choice of normally open, normally open high voltage, normally closed or changeover contacts.
A flange mounting reed sensor 28.57mm x 19.05mm x 6.35mm (1.125" x 0.750" x 0.259") with a choice of normally open, normally open high voltage, normally closed or changeover contacts.
A flange mounting reed sensor 28.57mm x 19.05mm x 6.35mm (1.125" x 0.750" x 0.259") with a choice of normally open, normally open high voltage, normally closed or changeover contacts.
A small surface mounting mounting reed sensor 22.00mm x 3.76mm x 3.57mm(0.870" x 0.148" x 0.141mm) with either J Foot or Gull Wing leads. Choice of normally open or change over contacts.
A miniature overmoulded reed sensor 16.00mm x 2.41mm x 2.41mm(0.630" x 0.095" x 0.095mm) with either straight or Gull Wing leads. Normally open contact.
A sub-miniature overmoulded reed sensor 11.43mm x 2.29mm x 2.29mm(0.450" x 0.090" x 0.090mm) with either straight or Gull Wing leads. Normally open contact.
A small lever arm reed sensor in a clip mounting frame with low operating force and an integral 2 pin connector. Normally closed contacts.
A robust lever arm reed sensor with integral vane and actuator magnet. Actuation occurs when vane is depressed. Normally closed or normally closed high voltage contacts.
A magnetically operated push button sensor with simple push fit clip mounting. Normally open contacts actuate when the plunger is depressed.
A magnetically operated push button sensor with simple push fit clip mounting. Large integral dome. Normally open contacts actuate when the dome is depressed.
A small sensor with integral float actuator and an M8 x 1.25mm pitch thread with a choice of normally open, normally open high voltage, normally closed or change over contacts.
A magnetically operated reed switch sensor for the detection of unidirectional shock levels with normally open contacts which actuate when set level of shock occurs.
Hall effect sensors
A robust stainless steel hall effect barrel sensor with an M12 x 1mm pitch thread, 46mm (1.810") long primarily for geartooth sensing. Protected against severe and automotive environments.
A miniature hall effect sensor with integral actuator magnet. Actuation occurs when a suitable vane passes through the slot between the magnet and hall element.
A miniature flange mounting hall effect sensor 25.5mm (1.004") x 11.00m (0.433") and only 3.00mm (0.118") high with a choice of digital, latching or programmable analogue outputs.
A flange mounting hall effect sensor with integral LED for visual indication of operation, 34.00mm (1.339") x 14.00m (0.551") x 10.00mm (0.394") with a choice of digital or latching outputs.
A small flange mounting hall effect sensor occupying only 3.22cm² (0.500"²) board space with a choice of digital, latching or programmable analogue outputs.
A robust flange mounting hall effect sensor primarily for geartooth sensing. Protected against severe and automotive environments.